request quote

Carpet

January 25, 2010 at 10:25 am | Category: Remodeling Contractor



Installing your carpet isn’t a job everybody wants to take on. It can be hard on both your knees and your back, and if you don’t get it right, everybody can see where you made a mistake. However, installing carpet isn’t “rocket science,” and by using some specialized tools (available at most tool rental outlets) and being prepared to take your time, installing carpet is a job you can do by yourself.

What You’ll Need:
•Tack-less strips
•Stapler
•Hammer
•Utility knife
•Chalk line
•Measuring tape
•Rolling pin (or rental seam roller)
•Work gloves
•Safety glasses
•Knee pads

Rental Tools:
•Knee kicker
•Power stretcher
•Seam cutter
•Seaming iron
•Seam tape
•Wall trimmer
•Strip cutter
•Seam roller

Getting Ready

First, get rid of the old carpet. Start by removing the moldings around the floor and take the door off the entrance, so you can get the old carpet out and the new carpet in easier. Give the old carpet a good vacuuming so you won’t be breathing in dust, and then use a utility knife to cut the carpet into strips about 18 to 24 inches wide.

Start at one end and pull the carpet off the tack-less strips and roll it up in sections. Some people feel that you can reuse the existing underlay, but in most cases it will be worn out just like the carpet, so you’re better off getting rid of it as well.

Remove the existing tack-less strips and make sure the floor is clean and dry. This is a good time to check your subfloor and securely fasten any floorboards that may be loose so they won’t squeak under the new carpet (use 1 1/2″ screws into the underlying floor joists).

Install new tack-less strips around the perimeter of the room, but not in front of doorways. Leave a space of about 1/2″ between the strips and the wall, and be sure the pins or tacks face towards the wall. (They’re called tack-less strips even though they have two or three rows or very sharp tacks, because using these “tack-less strips” means you don’t need to “tack” carpet down.) At corners, make sure the tack-less strips are butted tightly against each other.

Laying the Underpad

Put the underpad down in strips that overlap the tack-less strips. Align the strips against each other – don’t overlap them – then staple the underlay down along the inside edge of the tack-less strip. Trim the excess underlay along the inside of the tack-less strip and use duct tape to seal the seams.

Laying the Carpet

To install carpet properly, you need to start with a piece that overlaps the edge of the floor by 4 to 6 inches. The overlay can then be trimmed so the carpet fits properly. To cut your first section, measure the room at its longest point and add 6 inches to that measurement. Mark the back of your carpet on both edges with that measurement and join the two marks with a chalk line. Fold the carpet over on itself, and using a straight edge and a sharp utility knife, cut through the backside of your carpet. Be sure to place a piece of scrap board underneath your cut line to protect the underlying carpet.

Seams

If your room is wide enough that you’re going to need another piece of carpet, follow the same process with the second piece – measure, mark and trim. Be sure the carpet pile is running the same way in both pieces, and that the carpet piece is large enough to overlap the wall by 4 to 6 inches, as well as overlapping the first piece of carpet by 4 to 6 inches. (Try to layout your carpet pieces so the seams won’t be in noticeable areas, but obviously sometimes that just isn’t possible.)

Where the carpet pieces will join, overlap the two pieces, and then using a utility knife or a rented seam cutter, cut through both pieces of carpet, ensuring the edges will match exactly. After cutting the carpet, center a piece of seaming tape on the floor underneath where they join, adhesive side up. Use the seaming iron to activate the adhesive (the iron goes on the tape, not on top of the carpet), and then butt the edges together and seal the seam with a rolling pin or a carpet roller.

Attaching the Carpet

Use a knee kicker to attach the carpet along one edge. A knee kicker is a solid metal tool about 18″ long with “teeth” that will grip the carpet on one end, and a heavily padded “butt” on the other. Place the toothed end of the kicker about 3″ from the wall and drive your knee forcefully into the padded end of the tool. This will stretch the carpet over the tack-less strip where the tacks will grab it and hold it firmly in place.

A carpet stretcher will finish attaching the carpet. A carpet stretcher is similar to knee kicker, but much longer. Put one end of the carpet stretcher against the wall where the carpet is already attached and place the other end about 6 inches from the far wall. The carpet stretcher also has teeth to grip the carpet, and when you push on the activation lever, it will stretch the carpet over the tackless strip near the far wall.

Work your way around the room stretching the carpet over the tackless strips, and trim the carper near the wall with a utility knife or a wall trimmer.

Finishing Up

Using a stair tool, tuck the carpet down into the gap between the tack-less strips and the wall. At the doorway, trim the carpet so the edge is centered under the closed door and install a door edge strip. Finally, cut any vent openings and install the molding on the baseboards.


If you are looking for a Denver remodeling contractor then please call 303-833-4715 or complete our online request form.